Register your product and get support at www.philips.com/welcome Universal remote control SRU 5120/87 EN Remote control IT ES PT Telecomando Mando a distancia Telecomando 3 12 21 31 40 50 60 70 GR ËϯÂÈÚÈÛÙ<ÚÈÔ TR Uzaktan kumanda RU PL CS Pilota Dálkového ovládání 79 2 1 2 3 4 5 6 Your universal remote control Installing the remote control 2.1 Inserting the batteries 2.2 Testing the remote control 2.3 Setting the remote control Keys and functions Extra possibilities 4.1 Adjusting device selection (Mode keys) 4.2 Restoring the original remote control settings Frequently asked questions Need help? Code list of all brands / equipment Information to the Consumer 3 3-7 3 4 4-6 7-8 8-9 8-9 9 10 11 88-97 100 1 Your universal remote control Congratulations on your purchase and welcome to Philips. To fully benefit from the support that Philips offers, register your product at www:philips.com/welcome. For quick, clean and easy setup go to: www.philips.com/urc After installing the universal remote control SRU 5120 you can operate a maximum of 2 different devices with it: TV and DVD player/HDD/recorder or VCR. 2 2.1 1 Installing the remote control Inserting the batteries Press the cover inwards and slide it in the direction of the arrow. 1 1 2 3 Place two AAA type batteries into the battery compartment, as shown. Replace the cover and click it firmly into place. Installing the remote control 3 ENGLISH Table of contents 2.2 Testing the remote control The remote control has been programmed to operate most Philips devices. Because the SRU 5120 may use different signals for each brand and even for different models of the same brand, it is advisable to test whether your device responds to the SRU 5120.The example below (TV) instructs you how to do this.You can repeat the same steps for other devices (DVD player/recorder or VCR) which you want to operate using the SRU 5120. Example of TV: 1 Turn your TV on manually or use the original remote control.Tune to channel 1. 2 Press the TV key to select TV. · The key lights up. 2 · If the key does not light up, check whether the batteries are properly inserted (see `2.1 Inserting the batteries'). 2 ENGLISH 3 Check whether all the keys are working. 3 For an overview of the keys and their functions see `3. Keys and functions'. · If the TV responds as it should to all of the key commands the SRU 5120 is ready for use. 3 Tip If the device does not respond at all or not to all of the key commands, follow the instructions under `2.3 Setting the remote control', or for online setup go to: www.philips.com/urc. 2.3 Setting the remote control This is only necessary if your device does not respond to the SRU 5120. If that is the case, the SRU 5120 does not recognize the brand and/or model of your device and you need to program the remote control to do so.The example below (TV) instructs you how to do this. You can repeat the same steps for other devices (DVD player/ recorder or VCR) which you want to operate using the SRU 5120. 4 Installing the remote control Example of TV: 1 Turn on the TV manually or use the original remote control.Tune in to channel 1. 2 Look up the brand of your TV in the code list at the back of this manual. A four-figure code is shown for each brand. Note the code for your brand. 4 4 Be careful! There are separate tables for TV, DVD and VCR. Make sure you use the codes from the correct table. 3 Press the TV key until it flashes twice and then remains lit. 5 5 4 Then enter the code noted in step 2 using the numeric keys. 6 6 5 · The TV key now flashes twice. · If the key flashes once for an extended period, the code has not been entered properly or the wrong code has been entered. Start again from step 2. Press and hold the Stand-by key of the SRU 5120 until your TV switches off (stand-by). 7 Then release the key immediately. 7 · The SRU 5120 is now set to operate your TV. Installing the remote control 5 ENGLISH 6 ENGLISH 7 Check if you can operate all functions on your TV with the SRU 5120. · If a key does not function properly, keep it pressed until it works. Then release the key immediately. Repeat this for every key that does not work. · If the TV responds to all of the key commands, the SRU 5120 is ready for use. Do not forget to note your code. Keep the TV key pressed for 5 seconds to exit setup mode. 8 · When no key is pressed for 2 minutes or more the remote control will exit setup mode automatically. When setting the remote control for other devices, be sure to enter and exit setup mode with the appropriate mode key. DVD for DVD player/ recorder and VCR. Full search setup If your code does not work or if the brand of your device is not mentioned in the code list, you can try setting the remote control with full search setup. 1 Press the mode key of the device you wish to set up the remote control for. E.g. the TV key. Press the key until it flashes twice and then remains lit. 9 9 2 Press and hold the Stand-by key of the SRU 5120 until your TV switches off (stand-by). 10 Then release the key immediately. 10 · The SRU 5120 is now set to operate your TV. Full search setup takes about 5 minutes. 6 Installing the remote control The illustration on page 2 gives an overview of all keys and their functions. 1 2 switches TV or DVD on or off. · Text TV on/off (TV). · disc menu (DVD). / FAV(orites) · Electronic Program Guide (TV). · list of favorite channels. / HDD · wide screen TV (TV). · Hard Disk Drive menu (DVD-R). / LIVE · Text TV off (TV). · live program on currently selected channel (TV, Radio). 3 Text TV color keys. Used in text mode and in some on-screen menus. 4 MENU turns the menu on and off. 5 Cursor keys cursor up, down, left, right in a menu. 6 INFO displays on-screen channel information (TV). 7s mutes the TV sound. 8 - VOL + adjusts the TV volume. 9 Numeric keys direct choice of channels and other functions. 10 A/V switches between external inputs of your equipment. 11 5 / PICTURE · rewind (DVD/VCR). · changes picture/screen settings (TV). 2 / AUDIO · play (DVD/VCR). · changes audio settings (TV). 6 / ENLARGE · wind (DVD/VCR). · enlarges Text TV picture (TV). 9 / SUBTITLE · stop (DVD/VCR). · changes subtitle settings (TV). 0 record (DVD/VCR). ; / HOLD · pause (DVD/VCR). · holds current Text TV page (TV). 12 / selects between one- and two-figure channel numbers (TV). 13 P1P / TITLE · selects previous programme/ channel (TV). · title, chapter (DVD). 14 - PROG + / K J · selects a previous or following channel (TV). · selects a previous or following track (DVD). 15 OK confirms your selection. 16 BACK jumps back one level in the menu or turns off the menu. 7 y Stand-by / DISC Keys and functions ENGLISH 3 Keys and functions 17 TV / DVD ENGLISH device mode selection keys: · select TV or DVD mode. · blink when the remote control is set up for the selected device. · light up when a remote control command is sent to the selected device. Note If the device does not respond at all, or not to all of the key commands, follow the instructions under `2.3 Setting the remote control'. 4 Extra possibilities 4.1 Adjusting device selection (Mode keys) The SRU 5120 is default set for operating TV or DVD. You can select the device you wish to operate with the TV and DVD keys. Each mode key allows operation of one device only. If desired, you can program the keys to select a different kind of device. For example, if you want to operate a second TV. In the following example you will see how to configure the DVD key for a second TV. 1 2 Switch on the second TV. Press the DVD key to select DVD. · The key lights up. 11 11 3 Then keep keys 1 and 6 on the SRU 5120 pressed simultaneously for three seconds, until the DVD key lights up. 12 12 8 Extra possibilities 4 Press keys 9, 9 and 2 in that order. 13 ENGLISH 13 5 Press the TV key to select TV. Press the key until it flashes twice and then remains lit. 14 14 · The DVD key flashes twice. The DVD key will now allow you to operate your second TV. 6 Program the SRU 5120 to operate the second TV. See `2.3 Setting the remote control'. 4.2 1 Restoring the original functions of your remote control Keep keys 1 and 6 on the SRU 5120 pressed simultaneously for three seconds, until one of the mode keys (TV or DVD) flashes twice and then remains lit. 15 15 2 Press keys 9, 8 and 1, in that order. 16 16 · The mode key (TV or DVD) flashes twice. All original functions have now been restored and any extra functions have been deleted. Extra possibilities 9 5 Frequently asked questions ENGLISH In this chapter you find answers to the most frequently asked questions about your universal remote control. How do I set the remote control for combo devices (TV/VCR, TV/DVD, DVD/VCR, etc)? Some combo devices require you to set up two different source selection keys to control both parts of the combo device. For example, if you have a TV/DVD combo, you might need to set up one code under the TV key to control the TV and a separate code under the DVD key to control the DVD. The device I want to operate does not respond and the mode key (TV or DVD) does not flash when I press a key. Replace the old batteries with two new AAA batteries. The device I want to operate does not respond but the mode key (TV or DVD) does flash when a key is pressed. Point the SRU 5120 at the device and make sure that there are no obstructions between the SRU 5120 and the device. The SRU 5120 does not respond properly to commands. Try programming the SRU 5120 again. If the device still does not respond, call our helpline. The Text TV keys do not work. · Find out whether your TV is equipped with Text TV. · Maybe the SRU 5120 has to be adapted to the model of the device. Call our helpline for details. 10 Frequently asked questions If you have any questions about the SRU 5120, you can always contact us.You will find our contact details after the code list at the back of this manual. Read this manual carefully before you make a call. You can solve most of the problems yourself. If you cannot find any answers to your problems, write down the details of your device in the code list at the back of this manual. This will help our operators to assist you better and more quickly. Look up the numbers of the models in the instructions accompanying the device or on the back of your device.When you call our helpline, make sure the device is to hand so that our operators can help you determine whether your remote control is working properly. The model number of your Philips universal remote control is SRU 5120/87. Date of purchase: ......../......../........ (day/month/year) Need help? 11 ENGLISH 6 Need help? Sommario 1 2 ITALIANO 3 4 5 6 Telecomando universale Installazione del telecomando universale 2.1 Inserimento delle batterie 2.2 Test del telecomando 2.3 Impostazione del telecomando universale Tasti e relative funzioni Possibilità aggiuntive 4.1 Regolazione della scelta del dispositivo (tasti modalità) 4.2 Ripristino delle impostazioni originali del telecomando Domande frequenti Assistenza Elenco dei codici di tutte le marche/apparecchi Informazioni per il consumatore 12 12-16 12 13 14-16 16-17 17-19 17-18 19 19-20 20 88-97 100 1 Telecomando universale Congratulazioni per l'acquisto e benvenuto in Philips! Per trarre il massimo vantaggio dall'assistenza fornita da Philips, registrare il proprio prodotto sul sito: www.philips.com/welcome. Per un'installazione diretta, facile e veloce andare sul sito Internet: www.philips.com/urc Dopo aver installato il telecomando universale SRU 5120 è possibile far funzionare un massimo di 2 dispositivi diversi: TV e lettore DVD/HDD/recorder o VCR. 2 2.1 1 Installazione del telecomando Inserimento delle batterie Premere il coperchio verso l'interno e farlo scorrere nella direzione indicata dalla freccia. 1 1 2 3 Inserire due batterie AAA nel vano batterie come mostrato. Riposizionare il coperchio fino a che non scatta in posizione. 12 Installazione del telecomando Esempio relativo a un televisore: 1 Accendere il televisore manualmente o tramite il telecomando originale. Andare sul canale 1. 2 Premere il tasto TV per selezionare il televisore. · Il tasto si illumina. 2 · Se il tasto non si illumina, controllare che le batterie siano inserite correttamente (vedere il capitolo 2.1 Inserimento delle batterie). 2 3 Controllare che tutti i tasti funzionino. 3 Per una panoramica dei tasti e delle relative funzioni, vedere il capitolo '3.Tasti e relative funzioni'. · Se il televisore risponde correttamente a tutte le funzioni dei tasti, il modello SRU 5120 è pronto per l'uso. 3 Suggerimento Se il dispositivo non risponde, o non risponde a tutti i comandi, seguire le istruzioni del capitolo '2.3 Impostazione del telecomando' o, per istruzioni online, andare alla pagina: www.philips.com/urc. Installazione del telecomando 13 FRANÇAIS 2. ...